current: 1.5a voltage range: 50 - 1000v 1 of 2 silicon bridge rectifiers w005-w10 w005 w01 w02 W04 w06 w08 w10 maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 volts maximum rms voltage v rms 35 70 140 280 420 560 700 volts maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 volts maximum average forward current 0.375" (9.5 mm) lead length i f(av) 1.5 amps. peak forward surge current single half sine wave superimposed on rated load (jedec method) i fsm 50 amps. rating for fusing ( t < 8.3 ms. ) i 2 t 10 a 2 s maximum forward voltage per diode at i f = 1.0 amp. v f 1.0 volts maximum dc reverse current ta = 25 c i r 10 m a at rated dc blocking voltage ta = 100 c i r(h) 1.0 ma typical junction capacitance per diode (note 1) c j 14 pf typical thermal resistance (note 2) r q ja 36 c/w operating junction temperature range t j - 50 to + 150 c storage temperature range t stg - 50 to + 150 c notes : 1 ) measured at 1.0 mhz and applied reverse voltage of 4.0 volts. 2 ) thermal resistance from junction to ambient at 0.375" (9.5 mm) lead length p.c. board mounting. - 0.39 (10.0) 0.31 (7.87) 0.034 (0.86) 0.028 (0.71) ac + 1.10 (27.9) min. 0.22 (5.59) 0.18 (4.57) 0.22 (5.59) 0.18 (4.57) 0.22 (5.59) 0.18 (4.57) + - ac ac 1.00 (25.4) min. dimension in inches and (millimeter) features mechanical data glass passivated chip high case dielectric strength high surge current capability high reliability low reverse current low forward voltage drop ideal for printed circuit board case : reliable low cost construction epoxy : ul94v-o rate flame retardant terminals : plated leads solderable per polarity : polarity symbols marked on case mounting position : any www.sunmate.tw maximum ratings and electrical characteristics t a = 25 c unless otherwise specified single phase, half wave, 60hz, resistive or inductive load. for capacitive load, derate current by 20%. characteristic symbol unit weight : 1.29 grams ! ! ! ! ! ! ! ! ! ! ! ! ! utilizing molded plastic technique mil-std-202, method 208 guaranteed
2 of 2 fig.1 - derating curve for output fig.2 - maximum non-repetitive peak rectified current forward surge current 0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100 case temperature, ( c) number of cycles at 60hz fig.3 - typical forward characteristics fig.4 - typical reverse characteristics 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 forward voltage, volts 60 hz, resistive or inductive load. 1.2 0.6 0.3 1.5 10 10 1.0 40 0 50 0 20 10 0.01 1 80 0.01 0.1 0.1 100 140 0 20 40 60 120 percent of rated reverse voltage, (%) peak forward surge current, amperes average forward output current, amperes forward current, amperes reverse current, microamperes t j = 25 c pulse width = 300 m s 1 % duty cycle single half sine wave (jedec method) t j = 55 c t j = 100 c t j = 25 c 30 0.9 0.375(9.5mm) copper pads 0.22" x 0.22" (5.5 x5.5mm) pc board 20 www.sunmate.tw
|
